3D Bioplotter Research Papers

In this study, three-dimensional (3D) bioactive glass/lignocellulose (BG/cellulose) composite scaffolds were successfully fabricated by the 3D-bioprinting technique with N-methylmorpholine-N-oxide (NMMO) as the ink solvent. The physical structure, morphology, mechanical properties, hydroxyapatite growth and cell response to the prepared BG/cellulose scaffolds were investigated. Scanning electron microscopy (SEM) images showed that the BG/cellulose scaffolds had uniform macropores of less than 400 μm with very rough surfaces. Such BG/cellulose scaffolds have excellent mechanical performance to resist compressive force in comparison with pure cellulose scaffolds and satisfy the strength requirement of human trabecular bone (2-12 MPa). Furthermore, BG significantly increased the excellent hydroxyapatite-forming capability…

In this study, we printed three-dimensional (3D) titanium dioxide (TiO2)/chitin/cellulose composite photocatalysts with ordered interconnected porous structures. Chitin microparticles were mixed with cellulose in the N-methylmorpholine-N-oxide (NMMO) solution to prepare the printing “ink”. TiO2 nanoparticles were embedded on the chitin/cellulose composite in the NMMO removal process by water before the freeze-drying process to build the 3D cellulosic photocatalysts with well-defined porous structures. The 3D-printed TiO2/chitin/cellulose composites were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and Energy Disperse Spectroscopy (EDS). The XRD and FTIR analyses showed that chitin had an interference effect on the…

Extrusion-based three-dimensional (3D) printing of gelatin (Gel) is crucial for fabricating bone tissue engineering scaffolds via additive manufacturing. However, the thermal instability of Gel remains a persistent challenge, as it tends to collapse at mild temperatures. Current approaches often involve simply mixing Gel particles with various materials, resulting in biomaterial inks that lack uniformity and have inconsistent degradation characteristics. In this study, acetic acid was used to dissolve Gel and polycaprolactone (PCL) separately, producing homogeneous Gel/PCL dispersions with optimal pre-treatment performance. These dispersions were then combined and hybridized with nano-hydroxyapatite (n-HA) to create a composite printing ink. By evaluating the…

The growth plate (GP) is a crucial tissue involved in skeleton development via endochondral ossification (EO). The bone organoid is a potential research model capable of simulating the physiological function, spatial structure, and intercellular communication of native GPs. However, mimicking the EO process remains a key challenge for bone organoid research. To simulate this orderly mineralization process, we designed an in vitro shCav3.3 ATDC5-loaded gelatin methacryloyl (GelMA) hydrogel model and evaluated its bioprintability for future organoid construction. In this paper, we report the first demonstration that the T-type voltage-dependent calcium channel (T-VDCC) subtype Cav3.3 is dominantly expressed in chondrocytes and…

Additive manufacturing is one the most promising fabrication strategies for the fabrication of bone tissue scaffolds using biodegradable semi-crystalline polymers. During the fabrication process, polymeric material in a molten state is deposited in a platform and starts to solidify while cooling down. The build-up of consecutive layers reheats the previously deposited material, introducing a complex thermal cycle with impacts on the overall properties of printed scaffolds. Therefore, the accurate prediction of these thermal cycles is significantly important to properly design the additively manufactured polymer scaffolds and the bonding between the layers. This paper presents a novel multi-stage numerical model, integrating…

Three-dimensional (3D) bioprinting is a promising technique to construct heterogeneous architectures that mimic cell microenvironment. However, the current bioinks for 3D bioprinting usually show some limitations, such as low printing accuracy, unsatisfactory mechanical properties and compromised cytocompatibility. Herein, a novel bioink comprising hydroxyphenyl propionic acid-conjugated gelatin and tyramine-modified alginate is developed for printing 3D constructs. The bioink takes advantage of an ionic/covalent intertwined network that combines covalent bonds formed by photo-mediated redox reaction and ionic bonds formed by chelate effect. Benefiting from the thermosensitivity of gelatin and the double-crosslinking mechanism, the developed bioink shows controllable rheological behaviors, enhanced mechanical behavior,…

The emergence and innovation of three-dimensional (3D) bioprinting provide new development opportunities for tissue engineering and regenerative medicine. However, how to obtain bioinks with both biomimicry and manufacturability remains a great issue in 3D bioprinting. Developing intelligent responsive biomaterials is conducive to break through the current dilemma. Herein, a stepwise multi-cross-linking strategy concerning thermosensitive thiolated Pluronic F127 (PF127-SH) and hyaluronic acid methacrylate (HAMA) is proposed to achieve temperature-controlled 3D embedded bioprinting, specifically pre-cross-linking (Michael addition reaction) at low temperatures (4–20 °C) and subsequently self-assembly (hydrophobic interaction) in a high-temperature (30–37 °C) suspension bath as well as final photo-cross-linking (mainly thiol-ene…