3D Bioplotter Research Papers

An oxygen-resistant refractory high-entropy alloy is synthesized in microlattice or bulk form by 3D ink-extrusion printing, interdiffusion, and silicide coating. Additive manufacturing of equiatomic HfNbTaTiZr is implemented by extruding inks containing hydride powders, de-binding under H2, and sintering under vacuum. The sequential decomposition of hydride powders (HfH2+NbH+TaH0.5+TiH2+ZrH2) is followed by in situ X-ray diffraction. Upon sintering at 1400 °C for 18 h, a nearly fully densified, equiatomic HfNbTaTiZr alloy is synthesized; on slow cooling, both α-HCP and β-BCC phases are formed, but on quenching, a metastable single β-BCC phase is obtained. Printed and sintered HfNbTaTiZr alloys with ≈1 wt.% O shows excellent mechanical properties…

Single-crystal microstructure can bring high performance for many materials including piezoelectrics, semiconductors, and cuprate superconductors. Unlike single-crystal metals that can be machined into complex components, most single-crystal ceramics are limited to the shape of thin films or plates due to their brittleness. However, more designs of advanced devices need to break these geometric limitations. 3D-ink-printing can efficiently fabricate complex architectured ceramics, but the microstructure is polycrystals. Here, for the first time, we demonstrate a route to grow single-crystal on 3D printed ceramic-YBa2 Cu 3 O7-x (YBCO) superconductors that can simultaneously have complex architectures and high critical current density. An ink…

We present a new additive-reactive synthesis method where inks – cast into molds or 3D-additively extruded into architectured shapes – are reacted into intermetallic thermoelectric compounds. The new method, as demonstrated for equiatomic TiNiSn, combines: (i) extrusion printing (or casting) of inks containing Ni and Ti powders, (ii) debinding and reactive sintering to form a porous NiTi network, (iii) network infiltration with liquid Sn and subsequent reaction to synthesize the TiNiSn phase. Thin plates, created through this method, show high phase purity and low residual porosity. A thermoelectric figure of merit  = 0.47 ± 0.05 is achieved at 800 K, within the broad range…

Ni-Co-Fe-based high-entropy superalloys (HESAs) are fabricated into microlattices via a three-step process: (i) layer-by-layer extrusion of inks containing elemental powders (Ni, Co, Fe, Cr, Ti) and TiAl3 powders; (ii) sintering to densify and homogenize the struts; (iii) aging to achieve a γ/γ’ microstructure. The struts of the microlattices show a nearly pore-free and fully-homogenized microstructure. Increasing the Ti concentration from 4 at% (Al9Co26Cr7Fe16Ni38Ti4) to 9 at% (Al8Co25Cr7Fe15Ni36Ti9) leads to a significant increase in the volume fraction of strengthening γ’ precipitates, from 51 to 78 %. Furthermore, in the Ti-rich composition, the γ’ precipitates exhibit a sharp-edged cubic morphology with larger…

Additive manufacturing of objects with complex geometries from refractory metals remains very challenging. Here, we demonstrate the fabrication of tungsten sheet-gyroids via 3D ink-extrusion of WO3 nano-powder followed by hydrogen reduction and activated sintering with NiO additions, as an alternative route to beam-based additive manufacturing of tungsten and other high melting metals and alloys. The microstructure and mechanical properties of the tungsten sheet-gyroids are measured for various wall architectures and processing conditions. The original gyroid architecture, separating two equally-sized volumes, is modified to achieve double-wall gyroids (with three separate volumes) with higher relative densities. The compressive properties of these single-…

We present a novel additive manufacturing method for NiTi-Nb micro-trusses combining (i) extrusion-based 3D-printing of liquid inks containing NiTi and Nb powders, solvents, and a polymer binder into micro-trusses with 0/90° ABAB layers of parallel, ∼600 µm struts spaced 1 mm apart and (ii) subsequent heat-treatment to remove the binder and solvents, and then bond the NiTi powders using liquid phase sintering via the formation of a transient NiTi-Nb eutectic phase. We investigate the effects of Nb concentration (0, 1.5, 3.1, 6.7 at.% Nb) on the porosity, microstructure, and phase transformations of the printed NiTi-Nb micro-trusses. Micro-trusses with the highest Nb content…

Microlattices with orthogonal 0-90° architecture are 3D-extrusion printed from inks containing a blend of oxide powders (Co3O4, CuO, Fe2O3, and NiO) and metal powder (Cr). Equiatomic CoCrCuFeNi microlattices with ∼170 µm diameter struts are then synthesized by H2-reduction of the oxides followed by sintering and interdiffusion of the resulting metals. These process steps are studied by in-situ synchrotron X-ray diffraction on single extruded microfilaments (lattice struts) with ∼250 µm diameter. After reduction and partial interdiffusion at 600 ˚C for 1 h under H2, filaments consist of lightly-sintered metallic particles with some unreduced Cr2O3. A reduced, nearly fully densified (porosity: 1.6 ± 0.7%)…

Liquid ink-printing followed by sintering is used to fabricate WC-Co microlattices and cutting tools. The microstructure of WC-xCo (x=0.5-20 wt.%) is studied for a range of carbide-to-binder ratios and for various sintering temperatures. For 0.5≤Co≤5 wt.%, struts in microlattices exhibit residual porosity due to incomplete densification, even at the highest sintering temperature of 1650 °C. With 10 wt.% Co, fully dense lattice struts are achieved after sintering at 1450 °C for 1 h. For 1450-1650 °C sintering temperatures, the hardness of WC-xCo struts initially increases (due to increasing densification with increased Co) and then gradually decreases (due to an increase…

As an alternative to beam-based additive manufacturing, 3D ink-extrusion additive manufacturing is studied here for thermoelectric Bi2Te3, starting from Bi2O3+TeO2 oxide precursor powders. In situ synchrotron XRD in flowing H2 at elevated temperatures reveals the complex phase evolution upon co-reduction leading to the formation of Bi2Te3, Bi2TeO5 and Bi2TeO2. Sintering trials performed using optimal temperatures identified by in situ XRD show that low heating rates and extensive holding times are required to achieve full co-reduction to pure Bi2Te3. The formation of liquid Bi at the temperatures required for oxide reduction leads to local transient-liquid-phase sintering, creating a coarse-grained porous structure.…

Complex-shaped, finely-featured, ultra-high-melting ZrC/W composite structures were produced by coupling, for the first time, three-dimensional (3D) ink-extrusion printing with shape/size-preserving reactive melt infiltration (the Displacive Compensation of Porosity, DCP, process). Inks containing sub-micron WC powders were printed at ambient temperature into either fine-scale structures (sub-millimeter filaments) or into a larger-scale, finely-featured 3D structure (a centimeter-scale nozzle with a sub-millimeter-thick wall). After organic binder removal, the printed structures were sintered at 1650 °C for 1 h to achieve a porosity of 50%. The porous, rigid WC structures then underwent ambient pressure infiltration and reaction with Zr-Cu liquid at up to 1350…

The fabrication of 3D ink-printed and sintered porous Si scaffolds as electrode material for lithium-ion batteries is explored. A hierarchically-porous architecture consisting of channels (~220 μm in diameter) between microporous Si struts is created to accommodate the large volume change from Si (de)lithiation during electrochemical (dis)charging. The influence of sintering parameters on Si strut porosity and the resulting mechanical and electrochemical properties of the scaffolds are studied experimentally and computationally. Varying sintering temperatures (1150–1300 °C) and sintering times (1–16 h) the open porosity within the Si filaments can be tailored between 46 and 60%. Pore size (3–6 μm) and wall…

3D ink-extrusion of powders followed by sintering is an emerging additive manufacturing method capable of creating metallic microlattices. Here, we study the creation of hierarchically porous Fe or Ni scaffolds by 3D extrusion of 0/90° lattices from inks consisting of fine oxide powders (Fe2O3 or NiO, < 3 µm), coarse space-holder particles (CuSO4, < 45 µm) and a polymer binder within a solvent. After space-holder leaching and debinding of the lattices, a sintering step densifies the metallic Fe or Ni powders created by oxide reduction with H2, while maintaining the larger pores templated by the space-holder particles within the printed…

Titanium metal matrix composite microlattices are fabricated using 3D ink extrusion printing and sintering. The inks consist of TiH2+TiB2 or TiH2+TiC powder blends to form (i) Ti-TiB composites by dehydrogenation and in situ reaction of Ti + TiB2 to form Ti + TiB and (ii) Ti-TiC composites, where TiC remains stable during the sintering process. Rapid densification of the printed powder blend is achieved during pressureless sintering in vacuum at 1200 °C between 1 and 4 h, due to the small Ti particle size available from dehydrogenation of micron-sized TiH2. Near-full density Ti-TiB and Ti-TiC is achieved within individual lattice…

Cobalt-based superalloy microlattices were created via (i) three-dimensional-extrusion printing of inks containing a suspension of Co-, Ni- and W-oxide particles, (ii) H2-reduction of the oxides and sintering to a homogenous Co-Ni-W alloy, (iii) Al pack-cementation to deposit Al on the microlattice struts, followed by Al-homogenization. The resulting Co-(18–20)Ni-(5–6)W-(10–13)Al (at.%) microlattices, with 27–30% relative density and 350 μm diameter struts, display a peak in yield strength at 750°C, consistent with their γ/γ′ aged microstructure. Oxidation resistance is strongly improved compared to Al-free printed Co-Ni-W lattices, via the formation of an Al2O3 surface layer. However, the resulting Al depletion within the struts…

Cobalt-based superalloy microlattices with γ/γ′ microstructure are manufactured by combining two additive methods: ink-extrusion 3D-printing and pack-cementation surface alloying. First, a microlattice green structure is 3D-printed at ambient temperature from inks comprised of Co3O4, NiO, and WO3 powders, an elastomeric binder and solvents. Organic removal followed by oxide reduction under Ar-5% H2, sintering and homogenization at 1250 °C lead to a metallic microlattice with dense struts with uniform γ (fcc)-Co–22Ni–8W (at.%) composition. Second, aluminum is deposited on the strut surfaces via pack-cementation at 1000 °C, diffused at 1300 °C through the strut volume to achieve a uniform composition (Co–20Ni–6W–10Al or…

3D ink-extrusion of powders followed by sintering is an emerging alternative to beam-based additive manufacturing, capable of creating 3D metallic objects from 1D-extruded microfilaments. Here, in situ synchrotron X-ray diffraction and tomography are combined to study the phase evolution, alloy formation and sinter-densification of Fe-20Ni-5Mo (at.%) microfilaments. The filaments are

SnO2-Ag composites with designed architectures with sub-millimeter feature sizes can provide enhanced functionality in electrical applications. SnO2-Ag composites consisting of a ceramic SnO2 micro-lattice filled with metallic Ag are created via a hybrid additive manufacturing method. The multistep process includes: (i) 3D extrusion printing of 0/90° cross-ply micro-lattices from SnO2-7%CuO nanoparticle-loaded ink; (ii) thermal treatment in air to burn the binders and sinter struts of the SnO2 micro-lattice to ~94% relative density; (iii) Ag melt infiltration of channels of sintered micro-lattices. Densification of the SnO2 struts during air-sintering is accelerated by CuO liquid phase forming at 1100°C. During the subsequent…

Additive manufacturing of high-entropy alloys combines the mechanical properties of this novel family of alloys with the geometrical freedom and complexity required by modern designs. Here, a non-beam approach to additive manufacturing of high-entropy alloys is developed based on 3D extrusion of inks containing a blend of oxide nanopowders (Co3O4 + Cr2O3 + Fe2O3 + NiO), followed by co-reduction to metals, inter-diffusion and sintering to near-full density CoCrFeNi in H2. A complex phase evolution path is observed by in-situ X-ray diffraction in extruded filaments when the oxide phases undergo reduction and the resulting metals inter-diffuse, ultimately forming face-centered-cubic equiatomic CoCrFeNi alloy. Linked to the phase evolution…

Ni-29Mn-21.5Ga (at. %) wires are fabricated via a combination of (i) extrusion of liquid inks containing a binder, solvents, and elemental Ni, Mn, and Ga powders and (ii) heat treatments to remove the polymer binder and to interdiffuse and sinter the powders. To study the microstructural evolution, sintering mechanisms, and grain growth in these wires, both ex situ metallography and in situ X-Ray tomography were conducted while sintering at 800–1050 °C for up to 4 h. After debinding, Ga-rich regions melt and induce transient liquid phase sintering of the surrounding Ni and Mn powders, resulting in localized swelling of the wires and…

ungsten is of industrial relevance due its outstanding intrinsic properties (e.g., highest melting‐point of all elements) and therefore difficult to 3D‐print by conventional methods. Here, tungsten micro‐lattices are produced by room‐temperature extrusion‐based 3D‐printing of an ink comprising WO3–0.5%NiO submicron powders, followed by H2‐reduction and Ni‐activated sintering. The green bodies underwent isotropic linear shrinkage of ≈50% during the thermal treatment resulting in micro‐lattices, with overall 35–60% open‐porosity, consisting of 95–100% dense W–0.5%Ni struts having ≈80–300 μm diameter. Ball‐milling the powders and inks reduced the sintering temperature needed to achieve full densification from 1400 to 1200 °C and enabled the ink to be extruded…

The development of in situ fabrication methods for the infrastructure required to support human life on the Moon is necessary due to the prohibitive cost of transporting large quantities of materials from the Earth. Cellular structures, consisting of a regular network (truss) of micro-struts with ∼500 μm diameters, suitable for bricks, blocks, panels, and other load-bearing structural elements for habitats and other infrastructure are created by direct-extrusion 3D-printing of liquid inks containing JSC-1A lunar regolith simulant powders, followed by sintering. The effects of sintering time, temperature, and atmosphere (air or hydrogen) on the microstructures, mechanical properties, and magnetic properties of…

Ni-Mn-Ga magnetic shape memory alloy (SMA) micro-trusses, suitable for high magnetic field induced strains and/or a large magnetocaloric effect, are created via a new additive manufacturing method combining (i) 3D-printing ∼400 μm struts with an ink containing a polymer binder and elemental Ni, Mn, and Ga powders, (ii) binder burn-out and metallic powder interdiffusion and homogenization to create the final alloy, and (iii) further sintering to increase strut density. Controlled amounts of hierarchical porosity, desirable to enable twinning in this polycrystalline alloy, are achieved: (i) continuous ∼450 μm channels between the printed Ni-Mn-Ga ∼300 μm diameter struts (after sintering) and…

Inks comprised of metallic Fe or Ni powders, an elastomeric binder, and graded volatility solvents are 3D-printed via syringe extrusion and sintered to form metallic cellular structures. Similar structures are created from Fe2O3 and NiO particle-based inks, with an additional hydrogen reduction step before sintering. All sintered structures exhibit 92–98% relative density within their struts, with neither cracking nor visible warping despite extensive volumetric shrinkage (≈70–80%) associated with reduction (for oxide powders) and sintering (for both metal and oxide powders). The cellular architectures, with overall relative densities of 32–49%, exhibit low stiffness (1–6 GPa, due to the particular architecture used), high…

A new method for complex metallic architecture fabrication is presented, through synthesis and 3D-printing of a new class of 3D-inks into green-body structures followed by thermochemical transformation into sintered metallic counterparts. Small and large volumes of metal-oxide, metal, and metal compound 3D-printable inks are synthesized through simple mixing of solvent, powder, and the biomedical elastomer, polylactic-co-glycolic acid (PLGA). These inks can be 3D-printed under ambient conditions via simple extrusion at speeds upwards of 150 mm s–1 into millimeter- and centimeter-scale thin, thick, high aspect ratio, hollow and enclosed, and multi-material architectures. The resulting 3D-printed green-bodies can be handled immediately, are…