3D Bioplotter Research Papers

With the development of the internet-of-things for applications such as wearables and packaging, a new class of electronics is emerging, characterized by the sheer number of forecast units and their short service-life. Projected to reach 27 billion units in 2021, connected devices are generating an exponentially increasing amount of electronic waste (e-waste). Fueled by the growing e-waste problem, the field of sustainable electronics is attracting significant interest. Today, standard energy-storage technologies such as lithium-ion or alkaline batteries still power most of smart devices. While they provide good performance, the nonrenewable and toxic materials require dedicated collection and recycling processes. Moreover,…

The flow-induced supramolecular arrangement, or band texture, present in water-soluble anisotropic films prepared from blend solutions of hydroxypropyl cellulose and organosolv lignin is locked via esterification with bio-based polycarboxylic acids. Subsequent to shear casting of the blend solutions, the chemical cross-linking with citric acid-based cross-linkers and a dimerized fatty acid yields water-insoluble, anisotropic films prone to swelling in water. The liquid crystalline networks are analyzed by means of polarized optical microscopy, tensile testing, Fourier transform infrared, and swelling experiments. Depending on the cross-linker, the dry “banded” films reach up to 3.5 GPa in tensile modulus, 80 MPa in tensile strength…

3D printing technologies allow control over the alignment of building blocks in synthetic materials, but compositional changes often require complex multimaterial printing steps. Here, 3D printable materials showing locally tunable mechanical properties are produced in a single printing step of Direct Ink Writing. These new inks consist of a polymer matrix bearing biocompatible photoreactive cinnamate derivatives and up to 30 wt% of anisotropic cellulose nanocrystals. The printed materials are mechanically versatile and can undergo further crosslinking upon illumination. When illuminating the material and controlling the irradiation doses, the Young’s moduli can be adjusted between 15 and 75 MPa. Moreover, spatially…

We report on a procedure for the preparation, printing and curing of antibacterial poly(N-isopropylacrylamide) nanocellulose-reinforced hydrogels. These composites present a highly anisotropic microstructure which allows to control and modulate the resulting mechanical properties. The incorporation of such nanoparticles enables us to modify both the strength and the humidity-dependent swelling direction of printed parts, offering a fourth-dimensional property to the resulting composite. Antibacterial properties of the hydrogels were obtained by incorporating the functionalized peptide ε-polylysine, modified with the addition of a methacrylate group to ensure UV-immobilization. We highlight the relevance of well-adapted viscoelastic properties of our material for 3D printing by…

Owing to their ultralow thermal conductivity and open pore structure, silica aerogels are widely used in thermal insulation, catalysis, physics, environmental remediation, optical devices and hypervelocity particle capture. Thermal insulation is by far the largest market for silica aerogels, which are ideal materials when space is limited. One drawback of silica aerogels is their brittleness. Fibre reinforcement and binders can be used to overcome this for large-volume applications in building and industrial insulation, but their poor machinability, combined with the difficulty of precisely casting small objects, limits the miniaturization potential of silica aerogels. Additive manufacturing provides an alternative route to…

Cellulose is an attractive material resource for the fabrication of sustainable functional products, but its processing into structures with complex architecture and high cellulose content remains challenging. Such limitation has prevented cellulose‐based synthetic materials from reaching the level of structural control and mechanical properties observed in their biological counterparts, such as wood and plant tissues. To address this issue, a simple approach is reported to manufacture complex‐shaped cellulose‐based composites, in which the shaping capabilities of 3D printing technologies are combined with a wet densification process that increases the concentration of cellulose in the final printed material. Densification is achieved by…

The alignment of anisotropic particles during ink deposition directly affects the microstructure and properties of materials manufactured by extrusion-based 3D printing. Although particle alignment in diluted suspensions is well described by analytical and numerical models, the dynamics of particle orientation in the highly concentrated inks typically used for printing via direct ink writing (DIW) remains poorly understood. Using cellulose nanocrystals (CNCs) as model building blocks of increasing technological relevance, we study the dynamics of particle alignment under the shear stresses applied to concentrated inks during DIW. With the help of in situ polarization rheology, we find that the time period…